Cubitech 4CH Triplex Instrukcja Użytkownika Pobierz pdf (Strona 1)

Meter Jack

Monitor -

Please read this instruction Manual carefully for correct and effective use. If you do not

understand these instructions, contact your supplier for further information.

This sensor is designed to detect intrusion and to activate an alarm. It only provides an alarm

sign output, and is not an independent burglar-preventing device. If it's used abnormally,

faulty installation, improper maintenance or Acts of God, it will cause damage.

1.PARTS DESCRIPTION

2PH- 100BS/BQ Outdoor 300ft. (100m) / Indoor 600ft. (200m)

2PH- 150BS/BQ Outdoor 450ft. (150m) / Indoor 900ft. (300m)

NOTE

Response Time

Adjustment

Operation LED

(Transmitter only)

Horizontal

Adjustment

Terminals

Alarm LED

Lens

Tamper Switch

View Finder

Vertical

Adjustment

Screw

Unit Base

Mounting Plate

U-Shaped

Brackets

Attenuation Sheet

Cover

2.CAUTIONS ON INSTALL ATION

Detection Range

Detection Width

L A

180' (60m)

4.5' (1.5m)

300' (100m)

7.5' (2.5m)

450' (150m)

11.4' (3.8m)

Wrong place

Do not install the unit on places

where it may be splashed by

dirty water or direct sea spray.

Please make the Transmitter and Receiver within the required range as belows:

2PH-100BS/BQ Outdoor 300ft. (100m) / Indoor600ft. (200m)

2PH-150BS/BQ Outdoor 450ft. (150m) / Indoor 900ft. (300m)

The detection width can be calculated

with following formula :

Width A = 0.025 x Length (L)

Transmitter Receiver

Protection distance

Installation Height

Alignment Angle

To detect the intruder efficiently,

the sensors should be installed

within 32"~40" (80~100cm)

height.

Meter Jack

Monitor +

100M/150M TWIN PHOTOELECTRIC BEAM SENSOR

(80~100cm)

32"~40"

Attenuation LED

Channel Set SW

(100/150DQ only)

Remove all obstructions (trees,

clothes lines, etc.) Between

Transmitter and Receiver.

Do not install the unit on the unsteady

place.

Screws

Avoid strong light from the sun, headlights,

and direct shining on the Transmitter /

Receiver.

When strong light stays in optical axis for

a long time, it will hurt the product's lift.

The sensors can be adjusted with

Horizontal ±90°and Vertical ±10°

to fit big detection range.

Detection Range

M a n u a l I n s tr u c ti o n

Heating Unit : HT (Option)-150

Horizontal

(fine)Adjustment

1 2 3 4

Podsumowanie treści

Strona 1 - 2.CAUTIONS ON INSTALL ATION

Meter JackMonitor -Please read this instruction Manual carefully for correct and effective use. If you do not understand these instructions, contact

Strona 2 - 4.INSTALLATIONS

A.Wall MountingA-1. Pull out the wire through the wiring hole on the mounting plate and attach the plate to the wall with the screw ( 1/6〞x 3

Strona 3 - 6.BEAM FREQUENCY CHANGE

7.ALIGNMENT AND OPERATION900mV Over600mV to 900mV600mV Under5.RESPONSE TIME ADJUSTMENT0.70.05( Receiver )50ms300ms 700ms0.36.BEAM FREQUENCY CHANGES

Strona 4 - Taiwan Security Net Co., Ltd

NOTE: 1. This unit is designed to detect an intruder and activate an alarm control panel. Being only a part of complete system, we ca

Komentarze do niniejszej Instrukcji

Brak uwag

Cubitech 4CH Triplex Instrukcja Użytkownika Strona 1

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Cyfrowe rejestratory wideo (DVR) Cubitech 4CH Triplex. 100M/150M TWIN PHOTOELECTRIC BEAM SENSOR [en] Instrukcja obsługi

Podsumowanie treści

Komentarze do niniejszej Instrukcji

Cubitech 4CH Triplex Instrukcja Użytkownika Strona 1

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Cyfrowe rejestratory wideo (DVR) Cubitech 4CH Triplex. 100M/150M TWIN PHOTOELECTRIC BEAM SENSOR [en] Instrukcja obsługi

Podsumowanie treści

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Cyfrowe rejestratory wideo (DVR) Cubitech 4CH Triplex